Board logo

標題: 班馬 H53c H53Fc AA High CRI 新頭燈 ( 更新 ) [打印本頁]

作者: X-Ray    時間: 2017-4-22 15:01     標題: 班馬 H53c H53Fc AA High CRI 新頭燈 ( 更新 )

本帖最後由 X-Ray 於 2017-5-22 22:20 編輯

班馬推出兩把高 CRI 的新頭燈:

第一把班馬新頭燈,使用AA 電池,預計 5月21日推出。
H53c AA Headlamp Neutral White High CRI

h53c.jpg

image.jpeg

Cree XP-L2 EasyWhite LED
Nominal CCT 4000K
Typical CRI: 93-95
Tint deviation: 2-step MacAdam ellipse
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High:  H1 285 Lm (0.9 hr)  or  H2  238 Lm (1.5 hr) / 171 Lm (2.2 hrs) / 106 Lm (3.8 hrs)
Medium:  M1 56 Lm (7.6 hrs)  or  M2  26 Lm (17 hrs) / 10.3 Lm (39 hrs) / 3.5 Lm (4.2 days)
Low:   L1  1.0 Lm (12 days)  or  L2   0.26 Lm (1 month) / 0.06 Lm (2 months) / 0.01 Lm (3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
80 degree spill
10 degree hot spot
Dimensions
Head Diameter: 0.86 inch (21.8 mm)
Length:    2.9 inch
Weight
1.1 oz (31 gram)
2.0 oz (56 gram) with an Eneloop AA battery
2.8 oz (79 gram) with an Eneloop AA battery and headband
Features
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade  aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Battery reverse polarity protection
Tempered optical grade glass
Preinstalled bezel down pocket clip
Orange peel reflector
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX7 (2 meters, 30 minutes)






第二把班馬新頭燈,使用AA 電池,預計 5月21日推出
使用霧面鏡片,Hi CRI 93-95。
H53Fc AA Headlamp Floody Neutral White High CRI

h53fc.jpg

Cree XP-L2 EasyWhite LED
Nominal CCT 4000K
Typical CRI: 93-95
Tint deviation: 2-step MacAdam ellipse
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High:         H1 276 Lm (0.9 hr)   or    H2  230 Lm (1.5 hr) / 165 Lm (2.2 hrs) / 102 Lm (3.8 hrs)
Medium:   M1 55 Lm (7.6 hrs)    or    M2   25 Lm (17 hrs) / 10 Lm (39 hrs) / 3.4 Lm (4.2 days)
Low:         L1  1.0 Lm (12 days)   or    L2   0.26 Lm (1 month) / 0.06 Lm (2 months) / 0.01 Lm (3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
Floody beam from frosted lens, with 90 degree beam spread
Dimensions
Head Diameter: 0.86 inch (21.8 mm)
Length:    2.9 inch
Weight
1.1 oz (31 gram)
2.0 oz (56 gram) with an Eneloop AA battery
2.8 oz (79 gram) with an Eneloop AA battery and headband
Features
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade  aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Battery reverse polarity protection
Tempered optical grade glass
Orange peel reflector
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX7 (2 meters, 30 minutes)






H53w AA Headlamp Neutral White
使用AA 電池,預計 6月15日推出

image.jpg

Cree XP-L2 EasyWhite LED
Nominal CCT 4500K
Minimum CRI: 80
Tint deviation: 3-Step
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High:         H1 330 Lm (0.9 hr)   or    H2  275 Lm (1.6 hr) / 198 Lm (2.3 hrs) / 122 Lm (4.2 hrs)
Medium:   M1 65 Lm (8.5 hrs)    or    M2   30 Lm (21 hrs) / 12 Lm (41 hrs) / 4.1 Lm (4.5 days)
Low:         L1  1.2 Lm (13 days)   or    L2   0.31 Lm (1.1 month) / 0.07 Lm (2.2 months) / 0.013 Lm (3.3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
80 degree spill
12 degree hot spot
Dimensions
Head Diameter: 0.86 inch (21.8 mm)
Length:    2.9 inch (75 mm)
Weight
1.1 oz (31 gram)
2.0 oz (56 gram) with an Eneloop AA battery
2.8 oz (79 gram) with an Eneloop AA battery and headband
Features
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade  aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Battery reverse polarity protection
Tempered optical grade glass
Orange peel reflector
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX8 (2 meters, 30 minutes)







H53Fw AA Headlamp Floody Neutral White
使用AA 電池,預計 6 月15日推出
使用霧面鏡片

image.jpg


image.jpeg

Cree XP-L2 EasyWhite LED
Nominal CCT 4500K
Minimum CRI: 80
Tint deviation: 3-Step
User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
Light Output (runtimes)
High:         H1 320 Lm (0.9 hr)   or    H2  267 Lm (1.6 hr) / 192 Lm (2.3 hrs) / 119 Lm (4.2 hrs)
Medium:   M1 63 Lm (8.5 hrs)    or    M2   29 Lm (21 hrs) / 12 Lm (41 hrs) / 4 Lm (4.5 days)
Low:         L1  1.2 Lm (13 days)   or    L2   0.3 Lm (1.1 month) / 0.06 Lm (2.2 months) / 0.01 Lm (3.3 months)
Beacon Strobe Mode: 0.2Hz Beacon at Low / 0.2Hz Beacon at H1 / 4Hz Strobe at H1 / 19Hz Strobe at H1
Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Panasonic Eneloop Pro AA batteries. Remaining battery power, about 10-20%, after step-down are not counted towards the runtimes.
Operating Voltage Range: 0.7V - 2.0V
Battery: One AA size NiMH, lithium or alkaline battery. Panasonic Eneloop or Eneloop Pro is highly recommended. Batteries are not included in the box.
Parasitic Drain: Negligible (much less than the self discharging of a battery)
Beam Type
Floody beam from frosted lens, with 90 degree beam spread
Dimensions
Head Diameter: 0.86 inch (21.8 mm)
Length:    2.9 inch (75 mm)
Weight
1.1 oz (31 gram)
2.0 oz (56 gram) with an Eneloop AA battery
2.8 oz (79 gram) with an Eneloop AA battery and headband
Features
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Automatic stepping down from High to Medium, and from Medium to Low when battery capacity is low
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade  aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Battery reverse polarity protection
Tempered optical grade glass
Orange peel reflector
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX8 (2 meters, 30 minutes)

圖片附件: h53c.jpg (2017-5-4 12:12, 22.31 KB) / 下載次數 391
https://wii.tw/~fogerdis/attachment.php?aid=95668&k=429c00eba97cbac9b80b675773b6cd44&t=1732366233&sid=sQVYJX



圖片附件: h53fc.jpg (2017-5-4 12:12, 22.68 KB) / 下載次數 301
https://wii.tw/~fogerdis/attachment.php?aid=95669&k=05d68428f0210beace6bf2aebb11ea32&t=1732366233&sid=sQVYJX



圖片附件: image.jpeg (2017-5-5 22:33, 24.7 KB) / 下載次數 345
https://wii.tw/~fogerdis/attachment.php?aid=95706&k=e9888b73f080b4ec8a05fd50ee97ff85&t=1732366233&sid=sQVYJX



圖片附件: image.jpg (2017-5-22 22:11, 22.76 KB) / 下載次數 345
https://wii.tw/~fogerdis/attachment.php?aid=95949&k=4c122f70c0d932c167579951766f0d66&t=1732366233&sid=sQVYJX



圖片附件: image.jpg (2017-5-22 22:11, 23.08 KB) / 下載次數 291
https://wii.tw/~fogerdis/attachment.php?aid=95950&k=3b1bba6fbd12995988ac5aad327e2b18&t=1732366233&sid=sQVYJX



圖片附件: image.jpeg (2017-5-22 22:11, 22.95 KB) / 下載次數 303
https://wii.tw/~fogerdis/attachment.php?aid=95951&k=106cb7e973f8ffda327a40fa1019f99f&t=1732366233&sid=sQVYJX


作者: kevingod1    時間: 2017-4-22 18:01

看來是SC5c MK2的頭燈版
相比之下頭燈的功率蠻收斂的,
續航能力應該會比較好吧.

斑馬這幾隻都沒公布續航時間...
作者: yy3070330703    時間: 2017-4-22 20:48

我覺得H1檔的亮度應該還會再修改,H1和H2亮度差距太小,特別區別開沒啥意思,285流明大概是降檔後的數據吧?

反正完整的數據都還沒出來,什麼都有可能
作者: ЮヰД    時間: 2017-4-22 20:54

班馬新頭燈,使用AA電池,預計5月21日推出
。H53c AA頭燈中性白色高CRI


Cree XP-L 2 EasyWhite LED
標稱CCT 4000K
典型CRI:93-95
色調偏差:2步MacAdam橢圓形
用戶可選等級:3個主要級別(高,中,低)。每個主要級別都可以編程到其兩個子級別之一。每個主要級別的第二個子級別可以進一步編程為不同的亮度級別。
光輸出(運行時間)
高:H1 285 Lm(hr)或H2 238 Lm(hr)/ 171 Lm(小時)/ 106 Lm(小時)
介質:M1 56 Lm(小時)或M2 26 Lm(小時)/ 10.3 Lm (小時)/ 3.5Lm(小時)
低:L1 1.0Lm(天)或L2 0.26Lm(天)/ 0.06Lm(天)/ 0。
01 Lm(個月) 信標閃光燈模式:0.2Hz信標低/ 0.2Hz信標H1 / 4Hz H1 / 19Hz頻閃在H1閃光燈
燈光輸出為ANSI(前)(OTF)值。運行時使用Panasonic Eneloop Pro AA電池測試(和估計的寄生漏極)。剩餘的電池電量,約10-20%,降低後不計入運行時間。
工作電壓範圍:0.7V - 2.0V
電池:一個AA尺寸的NiMH,鋰或鹼性電池。強烈建議您使用Panasonic Eneloop或Eneloop Pro。電池不包括在盒子中。
寄生排水:可忽略不計(比電池自放電少)
光束類型
80度溢出
10度熱點
尺寸
頭直徑:0.86英寸(21.8毫米)
長度:2。
作者: honmin87    時間: 2017-4-22 22:33

AA電池又高CRI..........斑馬最近狂推新產品呀!
作者: sddsww    時間: 2017-4-22 23:53

好东西,准备买个
作者: kevinlin909    時間: 2017-4-23 01:32

團一把吧…
作者: X-Ray    時間: 2017-4-23 10:59

這兩天,它推出兩把 AA 電池的新頭燈,
第二把使用 霧面玻璃,

H53c 及 SC5C MK II ,就是今年的目標了。
作者: msx543    時間: 2017-4-26 01:22

等團購開團囉
作者: X-Ray    時間: 2017-5-4 12:14

圖片終於出來。
作者: X-Ray    時間: 2017-5-22 22:17

這星期新推出兩把使用 AA 電池的新頭燈,
不了解為什麼推出這兩把,重覆性太高,
且價錢一樣。


image.jpeg
image.jpeg

圖片附件: image.jpeg (2017-5-22 22:17, 41.98 KB) / 下載次數 270
https://wii.tw/~fogerdis/attachment.php?aid=95952&k=e628b27e8fb12a9fc840776a19ce4399&t=1732366233&sid=sQVYJX



圖片附件: image.jpeg (2017-5-22 22:17, 26.22 KB) / 下載次數 267
https://wii.tw/~fogerdis/attachment.php?aid=95953&k=c4e733b3e995a261872c80eed800d65c&t=1732366233&sid=sQVYJX


作者: X-Ray    時間: 2017-5-22 23:03

今年班馬還會推出一個平價系列的電筒,
價格只有平常的ㄧ半,,接近,

4把 H 系列,有2 支使用 AA ,
1 支 使用 CR123,1 支 使用 18650,

另一個是 F 系列,有3 把,
一樣,1 支使用 AA ,
1 支 使用 CR123,1 支 使用 18650。
作者: kevingod1    時間: 2017-5-24 17:49

12# X-Ray

另外2隻純粹只是Floody版本而已,算是斑馬的慣例了吧,
我也蠻好奇斑馬的Eco系列會是什麼樣子的型態,
持續等待C3中...
作者: X-Ray    時間: 2017-5-24 19:12

出了非 High CRI 的產品,
不過今年得準備預算買這3把。




歡迎光臨 電筒王論壇 (https://wii.tw/~fogerdis/) Powered by Discuz! 7.0.0